< prev index next >
make/UpdateX11Wrappers.gmk
Print this page
*** 1,7 ****
#
! # Copyright (c) 2012, 2017, Oracle and/or its affiliates. All rights reserved.
# DO NOT ALTER OR REMOVE COPYRIGHT NOTICES OR THIS FILE HEADER.
#
# This code is free software; you can redistribute it and/or modify it
# under the terms of the GNU General Public License version 2 only, as
# published by the Free Software Foundation. Oracle designates this
--- 1,7 ----
#
! # Copyright (c) 2012, 2018, Oracle and/or its affiliates. All rights reserved.
# DO NOT ALTER OR REMOVE COPYRIGHT NOTICES OR THIS FILE HEADER.
#
# This code is free software; you can redistribute it and/or modify it
# under the terms of the GNU General Public License version 2 only, as
# published by the Free Software Foundation. Oracle designates this
*** 21,99 ****
# Please contact Oracle, 500 Oracle Parkway, Redwood Shores, CA 94065 USA
# or visit www.oracle.com if you need additional information or have any
# questions.
#
# This file is responsible for extracting the x11 native struct offsets to
# the xawt Java library. The tool needs to be run on the os/arch that
# will host the final jvm, thus the tool cannot be used when cross compiling.
! # To enable cross compiling, the two versions of the generated offset file,
! # sizes.32 and sizes.64 are committed into the source code repository.
! # These are the ones used.
!
! # However when not cross compiling, the offset generator tool is built and
! # run, to verify that it still generates the same sizes.32 and sizes.64.
!
! GENSRC_X11WRAPPERS :=
! # Put temporary c-code and executable to calculate offsets here.
! # Also put verification offset file here as well.
! GENSRC_X11WRAPPERS_TMP := $(SUPPORT_OUTPUTDIR)/gensrc/java.desktop/_x11wrappers
! # Put the generated Java classes used to interface X11 from awt here.
! GENSRC_X11WRAPPERS_DST := $(SUPPORT_OUTPUTDIR)/gensrc/java.desktop/sun/awt/X11
!
! # The pre-calculated offset file are stored here:
! GENSRC_SIZER_DIR := $(TOPDIR)/make/data/x11wrappergen
!
! # Normal case is to generate only according to target bits
! GENSRC_X11_VERSION := $(OPENJDK_TARGET_CPU_BITS)
! ifeq ($(OPENJDK_TARGET_CPU_BITS), 64)
! ifneq ($(OPENJDK_TARGET_OS), linux)
! # On all 64-bit systems except Linux, generate both 32 and 64 bit versions
! GENSRC_X11_VERSION := 32 64
! endif
! else
! ifeq ($(OPENJDK_TARGET_OS), solaris)
! # As a special case, solaris 32-bit also generates the 64-bit version
! GENSRC_X11_VERSION := 32 64
! endif
endif
! GENSRC_X11_SIZES_USED := $(addprefix $(GENSRC_X11WRAPPERS_TMP)/sizes., $(GENSRC_X11_VERSION))
! # Copy only the sizes.* files that are actually needed. WrapperGenerator picks up any it finds from the
! # file prefix it is given so those not needed need to be hidden.
! $(GENSRC_X11WRAPPERS_TMP)/sizes.%: $(GENSRC_SIZER_DIR)/sizes.%
! $(call MakeDir, $(@D))
! $(RM) '$@'
! $(SORT) $< > $@
! # Run the tool on the offset files copied from the source repository to generate several Java classes
! # used in awt.
! $(SUPPORT_OUTPUTDIR)/gensrc/java.desktop/_the.generated.x11: $(GENSRC_X11_SIZES_USED) $(BUILD_TOOLS_JDK)
! $(call MakeDir, $(GENSRC_X11WRAPPERS_DST))
! $(TOOL_WRAPPERGENERATOR) $(GENSRC_X11WRAPPERS_DST) $(GENSRC_SIZER_DIR)/xlibtypes.txt "gen" $(GENSRC_X11WRAPPERS_TMP)/sizes
! $(TOUCH) $@
!
! GENSRC_X11WRAPPERS += $(SUPPORT_OUTPUTDIR)/gensrc/java.desktop/_the.generated.x11
!
! ifneq ($(COMPILE_TYPE), cross)
! # This is not a cross compile, regenerate the offset file, so that we
! # can compare it with the version in the source code repository.
!
! # Generate the C code for the program that will output the offset file.
! $(GENSRC_X11WRAPPERS_TMP)/sizer.%.c: $(GENSRC_SIZER_DIR)/xlibtypes.txt $(BUILD_TOOLS_JDK)
! $(call LogInfo, Generating X11 wrapper ($*-bit version))
! $(call MakeDir, $(@D))
! $(TOOL_WRAPPERGENERATOR) $(@D) $(GENSRC_SIZER_DIR)/xlibtypes.txt "sizer" $*
! # use -m32/-m64 only if the compiler supports it
! ifeq ($(COMPILER_SUPPORTS_TARGET_BITS_FLAG), true)
! MEMORY_MODEL_FLAG="$(COMPILER_TARGET_BITS_FLAG)$*"
! endif
! SIZER_CFLAGS := \
-I$(TOPDIR)/src/hotspot/share/include \
-I$(TOPDIR)/src/hotspot/os/$(HOTSPOT_TARGET_OS_TYPE)/include \
-I$(SUPPORT_OUTPUTDIR)/modules_include/java.base \
-I$(SUPPORT_OUTPUTDIR)/modules_include/java.base/$(OPENJDK_TARGET_OS_INCLUDE_SUBDIR) \
-I$(TOPDIR)/src/java.base/share/native/libjava \
--- 21,67 ----
# Please contact Oracle, 500 Oracle Parkway, Redwood Shores, CA 94065 USA
# or visit www.oracle.com if you need additional information or have any
# questions.
#
+ ################################################################################
+
+ default: all
+
+ include $(SPEC)
+ include MakeBase.gmk
+ include NativeCompilation.gmk
+ include ToolsJdk.gmk
+
+ ################################################################################
# This file is responsible for extracting the x11 native struct offsets to
# the xawt Java library. The tool needs to be run on the os/arch that
# will host the final jvm, thus the tool cannot be used when cross compiling.
+ #
+ # Two versions of the generated offset file, sizes-32.txt and sizes-64.txt are
+ # committed into the source code repository. These are the ones used in
+ # GensrcX11Wrappers.gmk to generate the Java code during the build.
+ ################################################################################
! ifeq ($(COMPILE_TYPE), cross)
! $(error It is not possible to update the x11wrappers when cross-compiling)
endif
! X11WRAPPERS_OUTPUT := $(SUPPORT_OUTPUTDIR)/x11wrappers
! GENSRC_X11WRAPPERS_DATADIR := $(TOPDIR)/make/data/x11wrappergen
! BITS := $(OPENJDK_TARGET_CPU_BITS)
! # Generate the C code for the program that will output the offset file.
! $(X11WRAPPERS_OUTPUT)/src/data_generator.c: $(GENSRC_X11WRAPPERS_DATADIR)/xlibtypes.txt $(BUILD_TOOLS_JDK)
! $(call LogInfo, Generating X11 wrapper data generator source code)
! $(call MakeDir, $(@D))
! $(call ExecuteWithLog, $@, \
! $(TOOL_WRAPPERGENERATOR) gen_c_source $@ $(GENSRC_X11WRAPPERS_DATADIR)/xlibtypes.txt $(BITS))
! DATA_GENERATOR_INCLUDES := \
-I$(TOPDIR)/src/hotspot/share/include \
-I$(TOPDIR)/src/hotspot/os/$(HOTSPOT_TARGET_OS_TYPE)/include \
-I$(SUPPORT_OUTPUTDIR)/modules_include/java.base \
-I$(SUPPORT_OUTPUTDIR)/modules_include/java.base/$(OPENJDK_TARGET_OS_INCLUDE_SUBDIR) \
-I$(TOPDIR)/src/java.base/share/native/libjava \
*** 101,128 ****
-I$(TOPDIR)/src/java.desktop/$(OPENJDK_TARGET_OS_TYPE)/native/common/awt \
-I$(TOPDIR)/src/java.desktop/share/native/common/awt/debug \
-I$(TOPDIR)/src/java.desktop/share/native/libawt/awt/image/cvutils \
#
! # Compile the C code into an executable.
! $(GENSRC_X11WRAPPERS_TMP)/sizer.%.exe: $(GENSRC_X11WRAPPERS_TMP)/sizer.%.c
! $(call MakeDir, $(@D))
! (cd $(@D) && $(CC) $(MEMORY_MODEL_FLAG) -o $@ $< \
! $(X_CFLAGS) \
! $(X_LIBS) \
! $(SIZER_CFLAGS) -lc)
!
! .PRECIOUS: $(GENSRC_X11WRAPPERS_TMP)/sizer.%.exe $(GENSRC_X11WRAPPERS_TMP)/sizer.%.c
!
! # Run the executable create the offset file and check that it is identical
! # to the offset file in the source code repository.
! $(GENSRC_X11WRAPPERS_TMP)/sizes.%.verification: $(GENSRC_X11WRAPPERS_TMP)/sizer.%.exe
! $(call LogInfo, Verifying X11 wrapper sizes)
$(call MakeDir, $(@D))
! $(GENSRC_X11WRAPPERS_TMP)/sizer.$*.exe | $(SORT) > $@.tmp
! $(DIFF) $(GENSRC_X11WRAPPERS_TMP)/sizes.$*.verification.tmp $(GENSRC_X11WRAPPERS_TMP)/sizes.$*
! mv $@.tmp $@
! GENSRC_X11WRAPPERS += $(GENSRC_X11WRAPPERS_TMP)/sizes.$(OPENJDK_TARGET_CPU_BITS).verification
! endif
! GENSRC_JAVA_DESKTOP += $(GENSRC_X11WRAPPERS)
--- 69,98 ----
-I$(TOPDIR)/src/java.desktop/$(OPENJDK_TARGET_OS_TYPE)/native/common/awt \
-I$(TOPDIR)/src/java.desktop/share/native/common/awt/debug \
-I$(TOPDIR)/src/java.desktop/share/native/libawt/awt/image/cvutils \
#
! # Compile the generated C code into an executable.
! $(eval $(call SetupNativeCompilation, BUILD_DATA_GENERATOR, \
! PROGRAM := data_generator, \
! OUTPUT_DIR := $(X11WRAPPERS_OUTPUT)/bin, \
! EXTRA_FILES := $(X11WRAPPERS_OUTPUT)/src/data_generator.c, \
! CFLAGS := $(X_CFLAGS) $(DATA_GENERATOR_INCLUDES) $(CFLAGS_JDKEXE), \
! LDFLAGS := $(LDFLAGS_JDKEXE), \
! LIBS := $(X_LIBS) -lc, \
! OBJECT_DIR := $(X11WRAPPERS_OUTPUT)/objs, \
! ))
!
! # Run the executable to create the data file.
! $(GENSRC_X11WRAPPERS_DATADIR)/sizes-$(BITS).txt: $(BUILD_DATA_GENERATOR_TARGET)
! $(call LogInfo, Generating X11 wrapper data files)
$(call MakeDir, $(@D))
! $(call ExecuteWithLog, $(X11WRAPPERS_OUTPUT)/generation, \
! $(BUILD_DATA_GENERATOR_TARGET) | $(SORT) > $@)
! TARGETS += $(GENSRC_X11WRAPPERS_DATADIR)/sizes-$(BITS).txt
!
! ################################################################################
!
! all: $(TARGETS)
! .PHONY: all default
< prev index next >